称重传感器的专业的术语有哪些?

　　The conditions (humidity, pressure, temperature, etc.) of the medium surrounding the load cell.

　　测力传感器周围介质的条件(湿度，压力，温度等)。

　　Ambient Temperature--环境温度：

　　The temperature of the medium surrounding the load cell.

　　测力传感器周围介质的温度。

　　Angular Load Eccentric--角载荷偏心：

　　A load applied eccentric with the primary axis at the point of application and at some angle with respect to the primary axis.

　　偏心施加的负载，主轴在施加点处并相对于主轴具有一定角度。

　　Angular Load Concentric--角载荷同心：

　　A load applied concentric with the Primary axis at the point of application and at some angle with respect to the Primary axis.

　　在应用点处与主轴同心地施加的负载，并且相对于主轴以一定角度施加的负载。

　　Axial Load--轴向载荷：

　　A load applied along or parallel to and concentric with the primary axis.

　　沿着或平行于主轴线并与主轴线同心的负载。

　　Calibration--校准：

　　The comparison of load cell outputs against standard test loads.

　　称重传感器输出与标准试验载荷的比较。

　　Calibration Curve--校准曲线：

　　A record (graph) of the comparison of the load cell outputs against standard test loads.

　　称重传感器输出与标准试验负载比较的记录(图表)。

　　Combined Error--组合错误：

　　(Non linearity and Hysteresis) The maximum deviation from the straight line drawn between original no--load and rated load outputs expressed as percentage of the ratedoutput and measured on both increasing and decreasing loads.

　　(非线性和滞后)与原始空载和额定负载输出之间绘制的直线的最大偏差，表示为额定输出的百分比，并在增加和减小的负载上测量。

　　Compensation--补偿：

　　The utilization of supplementary devices, materials, or process to minimize known sources of error.

　　使用辅助装置，材料或过程以最小化已知的误差源。

　　Creep--蠕变：

　　The change in load cell output occurring with time while under load and with all environmental conditions and other variables remaining constant.

　　负载下负载单元输出随时间的变化，所有环境条件和其他变量保持不变。

　　Creep Recovery--蠕变恢复：

　　The change in no--load output occurring with time after removal of A load which had been applied for a specific period of time. Usually measured over a specific time period immediately following removal of rated load and expressed as a percent of rated output over a specific period of time.

　　空载输出的变化在去除已经应用特定时间段的A负载之后随时间发生。

　　通常在除去额定负载后立即在特定时间段内测量，并表示为在特定时间段内额定输出的百分比。

　　Deflection--偏转：

　　The change of length along the primary axis of the load cell between no--load and rated load conditions.

　　在空载和额定负载条件之间沿称重传感器主轴的长度变化。

　　Drift--漂移：

　　A random change in output under constant load conditions.

　　恒定负载条件下的输出随机变化。

　　Eccentric Load--偏心载荷：

　　Any load applied parallel but not concentric with the primary axis.

　　任何平行施加的负载，但不与主轴同心。

　　Error--错误：

　　The algebraic difference between the indicated and true value of the load being measured.

　　测量的负载的指示值和真实值之间的代数差。

　　Excitation, Electrical--励磁，电气：

　　The voltage or current applied to the input terminals of the load Cell.

　　施加到负载传感器输入端的电压或电流。

　　Frequency Response--频率响应：

　　The range of frequencies over which the load cell output will follow the sinusoidally varying mechanical input within specified Limits.

　　在此范围内，称重传感器输出将遵循指定限制内的正弦变化机械输入。

　　Output--输出：

　　The signal (voltage, current, pressure, etc.) produced by the load cell. Where the output is directly proportional to excitation, the signal must be expressed in terms of volts per volt, per ampere, etc., of excitation.

　　由称重传感器产生的信号(电压，电流，压力等)。

　　在输出与激励成正比的情况下，信号必须以伏特/伏特，每安培等的激励表示。

　　Output, Rated--输出，额定：

　　The algebraic difference between the outputs at no--load an at rated load.

　　空载和额定负载下的输出之间的代数差。

　　Rated Capacity (Rated Load)--额定容量(额定负载)：

　　The maximum axial load the load cell is designed to measure within its specifications.

　　称重传感器的最大轴向载荷设计为在其规格范围内进行测量。

　　Reference Standard--参考标准：

　　A force measuring device whose characteristics are precisely known in relation to a primary standard.

　　一种力测量装置，其特性相对于初级标准是精确已知的。

　　Resolution--解析度：

　　The smallest change in mechanical input which produces a change in the output signal.

　　机械输入中产生输出信号变化的最小变化。

　　Sensitivity--灵敏度：

　　The ratio of the change in output to the mechanical input.

　　输出变化与机械输入的比率。